Shopping Cart
No items added.
close
Navigation
Currency:
Manufacturers

ILS-01 Controller

SKU: BRC433
Quick overview Advanced Radio ILS-01 Lighting Controller.
$159.84

Welcome the ILS-01 Light system from Advanced Radio. The newest and most feature packed scale lighting system available today. The Advanced Radio ILS-01 controller was developed in consultation with many world known scale RC pilots and is designed to deliver super bright lighting when used with our matched LED lights..

Super Bright Lights

The Advanced Radio ILS-01 LED lights are so bright you will see them 100’s meters/yards away in bright sunny conditions. These lights are so bright that you get the best scale look in the air and on the ground.

Simple to use design
Our designers have worked hard to make using the ILS-01 Lighting system simple and easy-to-use. With 2 rotary dials you can easily choose over 2500 different pattern combinations. Just rotate, set and forget.

Built in simulation LEDs
The Advanced Radio ILS-01 comes with simulation LED built into the main unit so you can try 1000’s of combinations to simulate the desired lighting effect before plugging into your main lights. Hours of fun.

6 lighting channels on 10 physical outputs.
ILS-01 offers 6 separate lighting channels with 10 physical output connectors for example: left/right NAV or front/rear strobe etc.

Channel 1 – Strobe1/Beacon1 with 14 lighting patterns.
Channel 2 – Strobe2/Beacon2 with 16 lighting patterns.
Channel 3 – Strobe3/Navigation channel with 16 lighting patterns.
Channel 4 – Landing lights with on/off control.
Channel 5 – Afterburner1/Gun effect channel 1.
Channel 6 – Afterburner2/Gun effect channel 2.

 

Please Note: The ILS-01 is designed to work seemlesly with Advanced Radio 12Volt LED lights which have inbuilt current limiting.

If you purcahse the ILS-01 to use with LED lights other than our 12volt lights then they MUST BE CURRENT LIMITED with at minimum a 300ohm resistor in series with the LED light. Using the ILS-01 with other brand lights is not covered by warranty. 

ILS-01

Advanced Switching option
Switching the ILS-01 lighting module on and off is simple. Just plug a signal wire from your receiver and use one of your transmitter’s 3 stage switches or slider as the master control. The 3 stage switch is assigned as follows:

1)      Switch off (Master Switch) = All lights OFF.
2)      Switch position 1 = Strobes and NAV lights ON. Landing lights OFF.
3)      Switch position 2 = Strobes and NAV lights ON. Landing lights ON.

ILS-01 lighting system comes with the following Strobe/Beacon Patterns.

SW Position Switch1/Strobe1 Switch2/Strobe2 Strobe3/NAV
0 Short Flash Short Flash Short Flash
1 Long Flash Short Flash Opp Phase Short Flash Opp Phase
2 Double Short Flash Long Flash Long Flash
3 Double Long Flash Long Flash Opp Phase Long Flash Opp Phase
4 Short Short Long Flash Double Short Flash Double Short Flash
5 Long Long Short Flash Double Short Flash Opp Phase Double Short Flash Opp Phase
6 Short Long Short Flash Double Long Flash Double Long Flash
7 Long Short Long Flash Double Long Flash Opp Phase Double Long Flash Opp Phase
8 Rotating Beacon Short Long Short Flash Short Long Short Flash
9 Double R.B. Long Short Long Flash Long Short Long Flash
A Learn Nav On Switch Position Short Short Long Flash Short Short Long Flash
B* Learn Landing On Switch Position Long Long Short Flash Long Long Short Flash
C* Copy Strobe 2 to Nav Rotating Beacon Rotating Beacon
D* Learn After Burner ON Throttle PWM Rotating Beacon Opp Phase Rotating Beacon Opp Phase
E* No Effect Switched On Switched On
F* Factory Reset Beacon Flash Beacon Flash

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

With this amount of flexibility you are guaranteed to have the right lighting scheme for your model.

 

Click Here to view the ILS-01 quick start guide

 

Whats included in the kit:

The stand alone controller has be designed for your new giant scale project to give that extra scale flair to your model and includes the ILS-01 master module and all the lights necessary for your project.

The Scale Basic Jet Lighting kit includes:

1 x (ILS-01) master lighting module

 

Optional afterburner ring

For the turbine pilots the ILS-01 also comes with a 2 channel afterburner system built right in. When you add the optional afterburner ring we combine amber (orange) and blue high intensity LEDS to give a realistic afterburner color. The dual afterburner channels allow the ILS-01 to automatically adjust the orange/blue combination for the most realistic afterburner look.

Afterburner

Specifications:

- Super Bright long life 12V LED Bulbs - visible up to a mile/kilometer away in bright sunny conditions.

- 10 physical outputs among 6 separate lighting channels. No need for ugly Y lead connectors.

- For turbine models - dual afterburner port for dual colour afterburner ring. (Afterburner ring sold separately)

- For non turbine models dual AUX ports for gun simulatpion.

- Master Control to turn lights on and off with via your transmitter.

- Separate switchable landing lights.

- Over 2500 different Strobe combinations on 3 channels.

- Battery Input: (10.6volts – 12volts) 3S Lipo or 3S lion. (Recommended 1100ma minimum capacity)

- Dimensions: 70mm x 40mm 20mm (2.75 x 1.57 x 0.78 inches).

Product description

Welcome the ILS-01 Light system from Advanced Radio. The newest and most feature packed scale lighting system available today. The Advanced Radio ILS-01 controller was developed in consultation with many world known scale RC pilots and is designed to deliver super bright lighting when used with our matched LED lights..

Super Bright Lights

The Advanced Radio ILS-01 LED lights are so bright you will see them 100’s meters/yards away in bright sunny conditions. These lights are so bright that you get the best scale look in the air and on the ground.

Simple to use design
Our designers have worked hard to make using the ILS-01 Lighting system simple and easy-to-use. With 2 rotary dials you can easily choose over 2500 different pattern combinations. Just rotate, set and forget.

Built in simulation LEDs
The Advanced Radio ILS-01 comes with simulation LED built into the main unit so you can try 1000’s of combinations to simulate the desired lighting effect before plugging into your main lights. Hours of fun.

6 lighting channels on 10 physical outputs.
ILS-01 offers 6 separate lighting channels with 10 physical output connectors for example: left/right NAV or front/rear strobe etc.

Channel 1 – Strobe1/Beacon1 with 14 lighting patterns.
Channel 2 – Strobe2/Beacon2 with 16 lighting patterns.
Channel 3 – Strobe3/Navigation channel with 16 lighting patterns.
Channel 4 – Landing lights with on/off control.
Channel 5 – Afterburner1/Gun effect channel 1.
Channel 6 – Afterburner2/Gun effect channel 2.

 

Please Note: The ILS-01 is designed to work seemlesly with Advanced Radio 12Volt LED lights which have inbuilt current limiting.

If you purcahse the ILS-01 to use with LED lights other than our 12volt lights then they MUST BE CURRENT LIMITED with at minimum a 300ohm resistor in series with the LED light. Using the ILS-01 with other brand lights is not covered by warranty. 

ILS-01

Advanced Switching option
Switching the ILS-01 lighting module on and off is simple. Just plug a signal wire from your receiver and use one of your transmitter’s 3 stage switches or slider as the master control. The 3 stage switch is assigned as follows:

1)      Switch off (Master Switch) = All lights OFF.
2)      Switch position 1 = Strobes and NAV lights ON. Landing lights OFF.
3)      Switch position 2 = Strobes and NAV lights ON. Landing lights ON.

ILS-01 lighting system comes with the following Strobe/Beacon Patterns.

SW Position Switch1/Strobe1 Switch2/Strobe2 Strobe3/NAV
0 Short Flash Short Flash Short Flash
1 Long Flash Short Flash Opp Phase Short Flash Opp Phase
2 Double Short Flash Long Flash Long Flash
3 Double Long Flash Long Flash Opp Phase Long Flash Opp Phase
4 Short Short Long Flash Double Short Flash Double Short Flash
5 Long Long Short Flash Double Short Flash Opp Phase Double Short Flash Opp Phase
6 Short Long Short Flash Double Long Flash Double Long Flash
7 Long Short Long Flash Double Long Flash Opp Phase Double Long Flash Opp Phase
8 Rotating Beacon Short Long Short Flash Short Long Short Flash
9 Double R.B. Long Short Long Flash Long Short Long Flash
A Learn Nav On Switch Position Short Short Long Flash Short Short Long Flash
B* Learn Landing On Switch Position Long Long Short Flash Long Long Short Flash
C* Copy Strobe 2 to Nav Rotating Beacon Rotating Beacon
D* Learn After Burner ON Throttle PWM Rotating Beacon Opp Phase Rotating Beacon Opp Phase
E* No Effect Switched On Switched On
F* Factory Reset Beacon Flash Beacon Flash

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

With this amount of flexibility you are guaranteed to have the right lighting scheme for your model.

 

Click Here to view the ILS-01 quick start guide

 

Whats included in the kit:

The stand alone controller has be designed for your new giant scale project to give that extra scale flair to your model and includes the ILS-01 master module and all the lights necessary for your project.

The Scale Basic Jet Lighting kit includes:

1 x (ILS-01) master lighting module

 

Optional afterburner ring

For the turbine pilots the ILS-01 also comes with a 2 channel afterburner system built right in. When you add the optional afterburner ring we combine amber (orange) and blue high intensity LEDS to give a realistic afterburner color. The dual afterburner channels allow the ILS-01 to automatically adjust the orange/blue combination for the most realistic afterburner look.

Afterburner

Specifications:

- Super Bright long life 12V LED Bulbs - visible up to a mile/kilometer away in bright sunny conditions.

- 10 physical outputs among 6 separate lighting channels. No need for ugly Y lead connectors.

- For turbine models - dual afterburner port for dual colour afterburner ring. (Afterburner ring sold separately)

- For non turbine models dual AUX ports for gun simulatpion.

- Master Control to turn lights on and off with via your transmitter.

- Separate switchable landing lights.

- Over 2500 different Strobe combinations on 3 channels.

- Battery Input: (10.6volts – 12volts) 3S Lipo or 3S lion. (Recommended 1100ma minimum capacity)

- Dimensions: 70mm x 40mm 20mm (2.75 x 1.57 x 0.78 inches).

Additional information
Manufacturer: Advanced Radio
Customers who bought this item also bought

10 mm High Bright Landing LED light

High Bright White 10mm Barrel LED designed specifically as a landing light
$13.36

18mm Extreme White Landing LED Lens Light

Extreme White 18mm Lens LED designed as a Landing Light
$17.39

10 mm Green High Bright Navigation LED light

High Bright Green 10mm Barrel LED designed specifically as a Navigation Light
$13.36

6mm White 5v-12v LED

6mm High Bright White LED. designed to work with both 5v and 12v systems. Can be used to replace stock lights in kits and models.
$9.33

Adjustable Voltage Boost (Step Up) Regulator

Adjustable Voltage Boost Regulator range between 3.5v to 32v output.
$40.23

10 mm Red High Bright Navigation LED light

High Bright Green 10mm Barrel LED designed specifically as a Navigation Light
$13.36